Hot Water System Failed Unexpectedly? Here's What to Do Next

Hot Water System Failed Unexpectedly? Here's What to Do Next

Blog Article

Go Deal Now

Were you hunting for resources about How to Troubleshoot and Repair an Electric Water Heater?

Several contemporary homes use an electrical hot water heater for their heater, because of its comfort as well as simplicity of use. Nonetheless, similar to any other electric devices, troubles might occur with its use, unexpectedly. It can be truly irritating to wake up to a chilly shower rather than a warm one or having your bathroom with water that isn't warm enough or perhaps too warm. Whatever the instance might be, water heater issues can be fairly aggravating. Thankfully, we have actually made a checklist of possible solutions to your water heater concerns. There are a variety of aspects that might cause a number of these troubles, it could be a problem with the power supply, the electric burner, or the thermostat. Before doing anything, ensure you switch off the primary power supply for security. Whatever the trouble is, getting it fixed should not present way too much of a problem if you comply with these steps:

Check Your Power Supply:

As fundamental as this may appear, it is extremely required. Without sufficient power, your water heater will not function. So the first thing to do when your water all of a sudden stops working is to validate that it isn't a power trouble. Examine if the fuse is blown out or the circuit breaker tripped. If the circuit breaker is the problem, simply turn it off and on again. Change any type of broken or worn-out fuse. Evaluate the appliance with power after these changes to see if it's now functioning.

Check the Burner in the Hot Water Heater:

If it's not a power issue, then attempt looking into your heating element if it is still functioning. Examine each of your burner to make sure the trouble isn't with any one of them. If any one of them is malfunctioning, replace that part and afterwards inspect whether the warm water is back on.

Inspect Your Thermostat:

If your hot water heater still isn't functioning or the water appearing isn't hot sufficient, you may need to inspect the temperature settings on your upper thermostat. Make sure the circuit breaker is turned off prior to doing anything. Open the gain access to panel and also press the red switch for temperature reset above the thermostat. This ought to aid heat up the water. Transform the breaker back on and inspect if the trouble has been fixed.

Call A Specialist:

If after changing all damaged parts as well as resetting your temperature level, the water heater still isn't functioning, you might need to get in touch with an expert plumber for a professional point of view. The trouble with your heating system could be that the cold and hot faucets have been switched or it might be undersized for the quantity of warm water required in your house. Whatever the situation might be, an expert plumber would certainly assist fix the problem.

Conclusion

Water heater problems are not constantly significant. Many of them are due to minor concerns like a blown fuse or damaged burner. Changing the faulty components must work. However, if you are still not able to fix the issue, give a call to your closest plumber ahead to get it dealt with.

What Would Cause My Electric Water Heater to Stop Working?

Your water heater is one of the most forgotten-about appliances in your home—until it quits working. Once you realize that there’s no hot water, the water heater jumps up to become the most noticeable appliance you have. No one in your family will be happy until you get the water heater fixed.

To fix an electric water heater as soon as possible, follow the troubleshooting advice discussed below.

Basic Water Heater Troubleshooting

Fortunately, you may be restore the hot water supply simply by resetting the house circuit breaker for the water heater. A tripped circuit breaker is one of the top causes of water heater failures. Shut the hot water heater breaker off then turn it back on. Give the water heater a half hour to heat up (if it’s working) and then check for hot water through one of your faucets.

If you get hot water after resetting the breaker, then the problem may be fixed if the breaker inadvertently tripped and it doesn’t continue tripping.

If the water heater breaker trips again, then you’ll likely need to have a service technician examine and repair the water heater. The service technician will check the circuit breaker and electrical supply wiring for the water heater. A short in the supply wiring or a bad circuit breaker could be causing the breaker to trip. An internal failure such as a broken heating element can also cause the breaker to continue tripping.

When resetting the water heater circuit breaker doesn’t work at all, then the water heater may be getting power while an internal water heater failure is causing the problem.

Conduct Advanced DIY Water Heater Troubleshooting

If the water heater doesn’t work after resetting the high-temperature limit switch, then you’ll need to either conduct some advanced water heater troubleshooting or have a service technician diagnose and repair the water heater failure.

Sears Technicians created a safe and highly-successful DIY advanced troubleshooting video to help you determine the cause of a water heating failure if you want to try to fix the problem yourself. Follow the advice in this video to find and fix the cause of the heating failure on your own:

The video begins with the basic troubleshooting described in the first 2 sections described above. It then goes on to guide you through checking water heater components to safely find the cause of the water heating failure.

If you get to a point in the troubleshooting where you’re not completely confident that you can safely continue, schedule a service technician to diagnose and repair the water heater.

The DIY water heater troubleshooting shown in the above video differs from the diagnosis techniques that service technicians typically use when examining a water heater to find the cause of a heating failure. Safe DIY troubleshooting doesn’t rely on live voltage checks while service technicians often use live voltage checks to quickly find the cause of water heater failures.

While many DIY’ers have been able to find the cause of water heater failures using troubleshooting advice shown in the video, some failures such as a bad circuit breaker can only be found using live voltage checks which should only be conducted by a trained service technician.

Sears Technicians have the training, tools and expertise to quickly find the cause of a water heater failure. Rely on our technicians to diagnose and repair your water heater or any other appliance in your home that quits working.

While the technician is in your home, take advantage of appliance Cleaning & Maintenance offers that the tech discusses with you. Keeping your appliances well-maintained will help them work more efficiently and last longer. Regular professional maintenance will also help prevent costly breakdowns of the appliances you depend on every day.

https://www.searshomeservices.com/blog/what-would-cause-my-electric-water-heater-to-stop-working

I hope you enjoyed reading our excerpt on How to Troubleshoot and Repair an Electric Water Heater. Thanks for taking the time to read through our content. Sharing is caring. Helping people is fun. Thanks a bunch for your time. Kindly check our blog back soon.

Ensure plumbing integrity; reach out.

Report this page